Pureit Ultima RO+UV has a 7-stage purification process that removes invisible and harmful new-age contaminants like lead and mercury along with excess Total Dissolved Solids (TDS) to make your water tastier.
Stage 1 – Pre-Sediment Filter Removes fine and coarse particulate impurities/dirt and improves the life of the Carbon Filter.
Stage 2 – Pre-RO Carbon Filter Removes chlorine and organic impurities like harmful pesticides. It also absorbs bad taste and odour causing organic compounds from water.
Stage 3 – Post RO Carbon Sediment Filter Removes fine and coarse particulate impurities/dirt and improves the life of the RO membrane.
Stage 4 - RO Membrane Removes dissolved salts, hardness, pesticides, fluoride and heavy metals like arsenic, lead and mercury. It also removes microbial contaminants like bacteria, viruses, protozoa and cysts.
Stage 5 - UV Reactor Acts as an additional stage of purification to further inactive bacteria, viruses and parasites to deliver safe water.
Stage 6 - Natural Taste Enhancer, the last level of purification acts as a polisher and enhances the taste of purified water.
Stage 7 - Micro Filtration Membrane (MF) or Micro Filtration (MF) is added post-RO, which ensures that the water is purified not once but thrice

Pureit has a storage tank capacity of up to 10 litres. With no continuous input water, the average dispense capacity is 9.2 litres. The storage tank is fully automatic and well shielded. When you take water from the tank, the purification process starts automatically again and refills the storage tank.

Pureit can purify water up to 15 litres per hour depending on the device you have purchased. However, the time taken to purify depend on the life of the filters, the input water pressure, TDS and other impurities present in the water.

You need to call the Pureit Helpline and order the consumables. The customer care specialist will visit your place and replace the consumable/Germkill Kit at a nominal cost.

In case you cannot dispense water from the tap, then you need to first check whether the power supply is on. If it is on, then check if there are any fault indicators illuminated, or “ CHANGE GKK” and the Call Center Number is illuminated on the Digital Display Panel. Call the Pureit Helpline and get either the fault resolved or the Germkill Kit is replaced. If none of these lights are illuminated on the Digital Display Panel, then check if the Ball Valve is closed. If none of these cases are true, then please call Pureit Helpline for assistance.

Pureit Mineral RO+UV will purify potable water for the removal of hardness and other impurities to give you safe drinking water. if the input water has impurities normally not present in drinking water (high iron/turbidity/microbial contamination etc.) or the water is from an unknown resource (river /lake /pond/borewell etc.) then suitable pre-treatments may be required.

It is not recommended to open and service a device by an individual. Call our Pureit Helpline if you face any issue which requires servicing and opening the device.

There may be several reasons for this: While the Germkill Kits and the Pre-Sediment Filter have fixed replacements schedules, depending upon your input water quality the Pre-Sediment Filter might need a replacement even before your Purifier gives you the alert. In such cases, please contact the Pureit Helpline and get Presediment Filter replaced. The purifier will communicate the alert only if the purifier is in a switched on condition during the scheduled alert time. Post the completion of the scheduled alert time, Auto Shut off™ of water will be activated automatically, even if the purifier is in a switched off condition.

While the Germkill Kits™ and the Pre-Sediment Filter have a fixed replacement schedule, you might be required to change the filters in the interim depending on the quality of your input water. Should the tap flow rate be very low or if it is taking too long for the tank to fill, then please contact the Pureit helpline to change the membranes. These extra visits will be chargeable as per T&C.

No, recommendation is to throw the first cycle of water that is filled in the storage tank when the new Pureit purifier is installed and also whenever the Germkill Kit are replaced.

You can used stored water for 2 days. If it is not used for more than 2 days we advise you to discard that water, refill and then consume

For any after-sales support related to your Pureit device, please call our Careline at 16627, available every day from 8:00 AM to 12:00 AM.

Service time may vary based on the availability of spare parts and Germkill Kits (GKK).

Food safe, non-toxic plastics

Pre-Sediment filter- 1 number.

Pre-RO carbon filter- 1 number.

Mesh filter- 1 number.

Anti scalant cartridge- 1 number.

RO membrane- 1 number.

Integrated TDS + Post carbon filter- 1 number.

Flow restrictor 200cc- 1 number.

Meets stringent international criteria for microbiologically safe drinking water-e.g.,

Environmental Protection Agency (EPA), USA

Stage 1^st:

Pre-Sediment Filter: Removes fine & coarse particulate impurities/dirt & improves the life of carbon filter.

Stage 2^nd:
Pre-RO Carbon Filter: Removes chlorine & organic compounds like harmful pesticides. It also absorbs bad taste & odor causing organic compounds inside water.

Stage 3^rd:
Mesh Filter: Filters water further to ensure removal of finer particulate impurities.

Stage 4^th:
RO Membrane: Removes dissolved salts, hardness, pesticides and heavy metals like lead and mercury. It also removes microbial contaminants like bacteria, viruses, protozoa, cyst.

Stage 5^th:
UV Chamber: Acts as an additional stage of purification to further inactivate bacteria, virus & parasites to deliver safe water.

Stage 6^th:
Post RO Carbon Filter: This level of purification acts as a polisher and enhances the taste of purified water.

Stage 7^th:

Carbitrap: Filters water to further ensure removal of loose carbon particles.

Pureit Vital Max has a storage tank capacity of up to 6.5 to 7 liters under running water conditions. The storage tank is fully automatic and well shielded. When you take water out of the tank, the purification process starts automatically again and refills the storage tank.

Pureit Vital Max can purify water up to 24 liters per hour depending on the device you have purchased. However, the time taken to purify depends on the life of the filters, the input water pressure, TDS and other impurities present in water.

You need to call the Pureit Helpline and order the consumables. The customer care specialist will visit your place and replace the consumable/Germ kill Kit at a nominal cost.

Pureit Vital Max will purify potable water for removal of hardness and other impurities to give you safe drinking water. If the input water has impurities normally not present in drinking water (high iron/turbidity/microbial contamination etc. or the water is from an unknown resource (river /lake /pond / borewell etc.) then suitable pre-treatments may be required.

It is not recommended to open and service device by an individual. Call our Pureit Helpline if you face any issue which requires servicing and opening the device.

There may be several reasons for this: While the Germ kill Kits and the Pre-Sediment Filter have fixed replacements schedules, depending upon your input water quality the Pre-Sediment Filter might need a replacement even before your Purifier gives you the alert. In such cases, please contact the Pureit Helpline and get Pre sediment Filter replaced. The purifier will communicate the alert only if the purifier is switched on condition during the scheduled alert time. Post the completion of the scheduled alert time, Auto Shut off™ of water will be activated automatically, even if the purifier is in a switched off condition.

While the Germ kill Kits™ and the Pre-Sediment Filter have a fixed replacement schedule, you might be required to change the filters in the interim depending on the quality of your input water. Should the tap flow rate be very less or if it is taking too long for the tank to fill, then please contact the Pureit helpline to change the membranes. These extra visits will be chargeable as per T&C.

No, the recommendation is to throw the first cycle of water that is filled in the storage tank when the new Pureit purifier is installed and whenever the Germ kill Kit is replaced.

You can use stored water for 2 days. If it is not used for more than 2 days, we advise you to discard that water, refill and then consume.

Like other ions, the RO technology can also remove arsenic, fluoride and nitrates.

However, RO system is not recommended for arsenic level above 0.1 mg/L, fluoride level above 8.0 mg/L and iron level above 0.3 mg/L.

It is not recommended to use the reject water for any kind of human/pets consumption (drinking or cooking). It may be used for gardening or cleaning floors.

Please call the Pureit helpline - 16627. Our technicians will visit your house and guide you on the repairs required. There will be a nominal visiting charge and you would need to buy the parts required.

First switch off the ball valve if you find any leakage front the purifier and turn off the power switch. Check for any visual improper fitment and then call our Pureit helpline number and register a service request.

You need to replace / clean the sediment filter basis water quality and GKK approximately every 1 year from date of installation. In case of poor source water quality or low water line pressure few filters may need to be replaced before 1 year and are not part of warranty.

For any after-sales support related to your Pureit device, please call our Careline at 16627, available every day from 8:00 AM to 12:00 AM.

Service time may vary based on the availability of spare parts and Germkill Kits (GKK).

For any after-sales support related to your Pureit device, please call our Careline at 16627, available every day from 8:00 AM to 12:00 AM.

Service time may vary based on the availability of spare parts and Germkill Kits (GKK).

For any after-sales support related to your Pureit device, please call our Careline at 16627, available every day from 8:00 AM to 12:00 AM.

Service time may vary based on the availability of spare parts and Germkill Kits (GKK).

Pureit Marvella Slim RO+UV+MF has a 7-stage purification process which ensures you to get water that is ‘As Safe As Boiled Water’ and also removes excess Total Dissolved Solids (TDS) to make your water tastier.
Stage 1st
Pre-Sediment Filter: Removes visible dirt and impurities.
Stage 2nd:
Membrane Protector: Removes chlorine, harmful pesticides, bad taste, and odor-causing organic compounds, increasing the life of the RO membrane.
Stage 3rd:
Mini Filter: Filters water further to ensure the removal of finer particulate impurities.
Stage 4th:
RO Membrane: Removes dissolved salts, hardness, pesticides, and heavy metals like lead and mercury, and microbial contaminants like bacteria, viruses, protozoa, and cysts.
Stage 5th:
UV Chamber: Additional stage of purification that destroys bacteria, viruses, and parasites.
Stage 6th:
Micro Filtration (MF) Membrane^: Additional stage of purification to further purify water.
Stage 7th:
Post RO Carbon Filter: Acts as a polisher and enhances the taste of purified water.

Pureit has Storage Tank capacity of upto 8L. The storage tank is fully automatic and well shielded and as and when you take water out of the tank, the purification process starts automatically again and refills the Storage Tank.

Pureit can purify water upto 20 litres/hour depending on the device you have purchased. However, the time taken to purify depends on the life of the filters, the input water pressure, TDS and other impurities present in the water.

Like other ions, the RO technology can also remove fluoride and nitrates.

For any after-sales support related to your Pureit device, please call our Careline at 16627, available every day from 8:00 AM to 12:00 AM.

Service time may vary based on the availability of spare parts and Germkill Kits (GKK).

Pureit Classic can store 9 ltrs. of purified water at a time, but the total volume of the Pureit classic device is 23 ltrs

Every time you fill the top chamber of a 'Pureit Classic' water purifier with water, all of it will get purified, and will collect in the transparent chamber within a few hours. So you can keep filling the top chamber as often as you need. However, you must ensure that there is one inch of empty space left in the transparent chamber, and that you don't then pour any more water into the top chamber. If you don't do this, or if you forget to withdraw water from the transparent chamber, the system has been designed to overflow from the side. You may repeat as many cycles a day as you require.

The average flow-rate of the Pureit water purifier will depend upon the quality of the water that is put into the Pureit system, and may also vary with the life of the Pureit Germkill Processor. The flow-rate through the system will typically be in the region of 30-150 ml/min. This means that 9 litres of water would get purified in 1-5 hours, depending on the quality of input water. Please note that the flow rate will be much higher than that in the beginning of the Pureit Germkill Kit™ life. Whenever you feel that the flow from your Pureit water purification system has become unsatisfactorily low, you can wash Activated Carbon Filter. Cleaning will remove accumulated dirt on the Activated Carbon Filter and will improve the water flow. Please follow Activated Carbon Filter cleaning instructions mentioned in Troubleshooting. It must be remembered that the first time you use the system, and anytime else when you empty the Cleansing - Collection chamber (such as after prolonged nonuse) no water will come out into the transparent section for a few hours. This is because the Cleansing - Collection chamber has to get re-filled with water.

Input water may contain many materials which affect the taste of water. Of these, Pureit removes materials like oil, sand, soil, clay, dirt, decayed animal and plant waste, and harmful pesticide impurities and is therefore likely to improve the taste of water. However, Pureit does not remove some dissolved salts that may contribute to taste like sodium chloride salt, calcium and magnesium. In fact, Pureit retains some ‘good’ dissolved salts present in drinking water. This may affect the taste of water.

Yes, the water will be free of harmful germs, but there may not always be an improvement in taste. However, by pouring brackish/sea water into the Pureit, there may be a risk of choking the system, and the ‘Auto Shut-off’ mechanism may malfunction.

No, this is not a problem. The final stage of Pureit Classic i.e. Polisher removes all the residual chlorine from the water, giving you absolutely safe, odor free, great tasting and safe drinking water from the transparent chamber.

The first batch of water that gets purified in your new Pureit, or from a new 'Germkill Kit™', should be drained away when it collects in the transparent chamber. This batch of water may have a distinctive taste and needs to be drained out by opening the tap. It should be noted that even though the first batch of water may have a distinctive taste, it is completely safe, even if accidentally ingested. Once you drain away the first batch, you will get pure and great tasting water in subsequent batches.

The first batch of water that gets purified in your new Pureit, or from a new Germkill Kit, should be drained away when it collects in the transparent chamber. This batch of water may contain some black particles that have got loosened from inside the Polisher during transit. Black particles may also appear as a result of shifting or tilting Pureit or when you are using Pureit after several days. It should be noted that these black particles are a part of the Polisher’s specially designed porous filter derived from natural coconut shell and are therefore completely safe, even if accidentally swallowed. To remove these black particles, pour the collected water back into the top chamber and rinse the transparent chamber with Pureit water to remove any particles that may be stuck to the sides.

In some cases, as with colloidal clay suspensions and with soluble salts of calcium, magnesium, iron etc., the turbidity and colour may not be completely removed. In these cases please ensure that there are no deposits or scales in the Transparent Chamber – if these are there then clean them by using a disinfectant. Rinse the Transparent Chamber thoroughly with Pureit water. Once this is done, the output water will be microbiologically completely protected from harmful germs even if some colour persists.

We advise that you let the water stand in another container for some time until most of the dirt settles down. Now pour the water into Pureit. This will ensure that the system does not get prematurely choked.

The Pureit system, and the Germkill Kit™ has been made from good quality, food safe, non-toxic engineering plastics. These plastics will also not impart a smell to the water. Similar plastics are used in all high quality refrigerators.

The tap will come in repeated contact with hands, bottles and glasses. You need to ensure that as a result of these contacts the tap does not get contaminated with germs. In case you do find that the mouth of the tap has become dirty, clean and disinfect it with a dilute disinfectant such as bleach / hypochlorite (50 ppm available chlorine) solution then discard the first 2 litres of Pureit water that flows through the tap.

Yes, this can be done. If you are shifting the purifier from one location inside the home to another, we would advise that you first remove the water from the top chamber, the batching chamber, the transparent chamber, and the Cleansing Collection chamber, only then shift the purifier. If you have to shift the purifier to a location outside your home you also need to ensure that the purifier is properly packed for transportation. Do not use the purifier for getting drinking water while it is being transported. Also, if the device is out of use for more than 3 days, then on starting to use again, throw one cycle of water from transparent chamber.

If some part of Pureit breaks accidentally, please call Pureit helpline-16627. We will arrange to send you a replacement part. You will however have to pay for the replacement part.

Yes, we can arrange to do that for you if you wish. Please call us on our Pureit Helpline No. 16627, and we will arrange to get a water test done for you. This service will carry a fee.

For any after-sales support related to your Pureit device, please call our Careline at 16627, available every day from 8:00 AM to 12:00 AM.

Service time may vary based on the availability of spare parts and Germkill Kits (GKK).