Pureit Ultima RO+UV has a 7-stage purification process that removes invisible and harmful new-age contaminants like lead and mercury along with excess Total Dissolved Solids (TDS) to make your water tastier.
Stage 1 – Pre-Sediment Filter Removes fine and coarse particulate impurities/dirt and improves the life of the Carbon Filter.
Stage 2 – Pre-RO Carbon Filter Removes chlorine and organic impurities like harmful pesticides. It also absorbs bad taste and odour causing organic compounds from water.
Stage 3 – Post RO Carbon Sediment Filter Removes fine and coarse particulate impurities/dirt and improves the life of the RO membrane.
Stage 4 - RO Membrane Removes dissolved salts, hardness, pesticides, fluoride and heavy metals like arsenic, lead and mercury. It also removes microbial contaminants like bacteria, viruses, protozoa and cysts.
Stage 5 - UV Reactor Acts as an additional stage of purification to further inactive bacteria, viruses and parasites to deliver safe water.
Stage 6 - Natural Taste Enhancer, the last level of purification acts as a polisher and enhances the taste of purified water.
Stage 7 - Micro Filtration Membrane (MF) or Micro Filtration (MF) is added post-RO, which ensures that the water is purified not once but thrice

Pureit has a storage tank capacity of up to 10 litres. With no continuous input water, the average dispense capacity is 9.2 litres. The storage tank is fully automatic and well shielded. When you take water from the tank, the purification process starts automatically again and refills the storage tank.

Pureit can purify water up to 15 litres per hour depending on the device you have purchased. However, the time taken to purify depend on the life of the filters, the input water pressure, TDS and other impurities present in the water.

You need to call the Pureit Helpline and order the consumables. The customer care specialist will visit your place and replace the consumable/Germkill Kit at a nominal cost.

In case you cannot dispense water from the tap, then you need to first check whether the power supply is on. If it is on, then check if there are any fault indicators illuminated, or “ CHANGE GKK” and the Call Center Number is illuminated on the Digital Display Panel. Call the Pureit Helpline and get either the fault resolved or the Germkill Kit is replaced. If none of these lights are illuminated on the Digital Display Panel, then check if the Ball Valve is closed. If none of these cases are true, then please call Pureit Helpline for assistance.

Pureit Mineral RO+UV will purify potable water for the removal of hardness and other impurities to give you safe drinking water. if the input water has impurities normally not present in drinking water (high iron/turbidity/microbial contamination etc.) or the water is from an unknown resource (river /lake /pond/borewell etc.) then suitable pre-treatments may be required.

It is not recommended to open and service a device by an individual. Call our Pureit Helpline if you face any issue which requires servicing and opening the device.

There may be several reasons for this: While the Germkill Kits and the Pre-Sediment Filter have fixed replacements schedules, depending upon your input water quality the Pre-Sediment Filter might need a replacement even before your Purifier gives you the alert. In such cases, please contact the Pureit Helpline and get Presediment Filter replaced. The purifier will communicate the alert only if the purifier is in a switched on condition during the scheduled alert time. Post the completion of the scheduled alert time, Auto Shut off™ of water will be activated automatically, even if the purifier is in a switched off condition.

While the Germkill Kits™ and the Pre-Sediment Filter have a fixed replacement schedule, you might be required to change the filters in the interim depending on the quality of your input water. Should the tap flow rate be very low or if it is taking too long for the tank to fill, then please contact the Pureit helpline to change the membranes. These extra visits will be chargeable as per T&C.

No, recommendation is to throw the first cycle of water that is filled in the storage tank when the new Pureit purifier is installed and also whenever the Germkill Kit are replaced.

You can used stored water for 2 days. If it is not used for more than 2 days we advise you to discard that water, refill and then consume

For any after-sales support related to your Pureit device, please call our Careline at 16627, available every day from 8:00 AM to 12:00 AM.

Service time may vary based on the availability of spare parts and Germkill Kits (GKK).