Pureit Classic Mineral RO+MF 【 OFFICIAL 】 Pureit Water in Bangladesh

Introduction

About the Device

Pureit brings to you the Pureit Classic RO+MF^ with its superior RO purification technology that reduces the maintenance cost and at the same time increases the filter life by 2 times* as compared to ordinary water purifiers.

Lowest Maintenance Cost*

Think a water purifier always comes with a high maintenance cost? Think again. Pureit introduces the new classic RO+MF^, which reduces the maintenance cost per liter is 2 taka*

Double Filter Life

Gone are the days of changing the filter of your water purifier time and again. The Pureit Classic RO+MF^ has a long filter life of 3000 litres.

High Water Saving*

With water shortage being an ever-increasing problem, who doesn’t want to save water? The Pureit Classic RO+MF^ saves water up to 35% whereas ordinary RO saves water only up to 25%.

Features

100% RO Purified Water

All water passes through RO ensuring no mixing of purified and impure water. Only RO can remove harmful chemicals like Lead, Mercury, etc.

Mineral Catridge Included

Enriches water by adding essential minerals like Calcium and Magnesium.

Double Purity Lock

100% guarantee of safe and sweet water.

100% Food Grade Plastic***

Prevents harmful toxins from leaching into water.

Advanced 6 Stage Purification process with RO+MF^

Every drop of water you drink is sweet and always safe.

Water Level Indicator

Enriches water by adding essential minerals like Calcium and Magnesium.

Smart Power Mode

Device goes on stand-by once the tank is full, saving power.

6 Litres Water Storage Capacity

Specifications for the Device

Specifications for Water Purifier

Weight

(Complete Unit)
7.3 kg

Flow Rate **

Upto 10-12 Liters/Hour

6 Stage Purifying Technology

Pre-Sediment Filter, Pre-RO Carbon Filter, Mini Filter, Reverse Osmosis Membrane, Micro Filtration Membrane and Post-RO Carbon Filter

Membrane Type

Thin film composite spiral wound

Pump Type

Diaphragm pump, 24 V DC

% Recovery **

Typically 25%

TDS Reduction***

90% (Min.)

Power Rating

36 Watts Maximum

Pressure Rating

10–30 PSI****

Input Voltage

100 - 240 Vac; 50 Hz

Material of Construction

Food safe, non-toxic, engineering grade plastics

Length of Power Card

1.5 metres

Total Dissolved Solids in Input Water

Upto 1800 mg/lit

Total Hardness

500 mg/lit (max.)

Iron in Input Water

0.3 mg/lit (max.)

Turbidity of Input Water

1 NTU (Max)

Specifications for Germkill Kit

GKK Life: 3000 Litres*

Meets stringent international criteria for microbiologically safe drinking water - e.g. Environmental Protection Agency (EPA), USA

Material of Construction

Food safe, non-toxic, engineering grade plastics

GKK

Pre-Sediment Filter - 2 Nos. I Pre-RO Carbon Filter - 1 No. I Post-RO Carbon Filter - 1 No.
Mini Filter - 1 No. I RO Membrane - 1 No. I Micro Filtration Membrane - 1 No. in case of RO+MF^ I TDS Modulator - 1 No.

Product Manual

Download PDF

FAQs

How does Pureit Mineral RO+MF Classic purify my water?

Pureit Mineral RO+MF has a 6-stage purification process that removes invisible and harmful new age contaminants like lead and mercury along with excess Total Dissolved Solids (TDS) to make your water tastier.

Stage 1 – Pre-Sediment Filter Removes fine and coarse particulate impurities/dirt and improves life of the Carbon Filter. Stage 2 – Pre-RO Carbon Filter Removes chlorine and organic impurities like harmful pesticides. It also absorbs bad taste odour causing organic compounds from water Stage 3 – Mini Filter Filters water further to ensure removal of finer particulate impurities Stage 4 - RO Membrane Removes dissolved salts, hardness, pesticides, fluoride and heavy metals like arsenic, lead and mercury. It also removes microbial contaminants like bacteria, virus, protozoa and cysts. Stage 5 - Micro Filtration Membrane (MF) Micro Filtration (MF) is added post-RO, which ensures that the water is purified not once but twice Stage 6 - Post-RO Carbon Filter: Last level of purification acts as a polisher and enhances the taste of purified water

What is the storage capacity of Pureit Mineral RO+MF?

Pureit has storage tank capacity of upto 6 litres. The storage tank is fully automatic and well shielded and as and when you take water of the tank, the purification process starts automatically again and refills the storage tank

How much time does it take to purify water in Pureit Mineral RO+MF?

Pureit can purify water up to 10-12 litres per hour depending on the input water quality. However, the time taken to purify depend on the life of the filters, the input water pressure, TDS and other impurities present in water

Does Pureit Classic RO + MF^ remove fluoride and nitrates?

Like other ions, the RO technology can also remove fluoride and nitrates.

How will I get new consumables/membranes replaced?

You need to call the Pureit Helpline and order the consumables. The customer care specialist will visit your place and replace the consumable/Germkill Kit at a nominal cost.

What should I do if the flow rate from tap is low?

Please check the LEDs and see whether SF or GKK needs to be replaced as per the instructions in Advance Alert System section. If not then contact the Pureit Helpline for assistance.

What are all the consumables which are to be replaced?

You need to replace the Sediment Filter, Pre and Post RO Carbon Filters, RO Membranes, Micro Filtrations Membrane, Mini Filter and TDS Modulator when the GKK starts blinking RED. These parts can be bought together by ordering GKK

Can I drink first purification cycle of water from the purifier?

No, recommendation is to throw the first cycle of water that is filled in the storage tank when the new Pureit purifier is installed and also whenever the Germkill Kit are replaced.

What should I do if there is no purified water in the storage tank?

If there is no purified water in the storage tank, check the following 2ND LED light is red: This means that GKK life has ended. Call the helpline to get the GKK replaced 1st LED is not lit: This could mean that the input water pressure is not sufficient, check for input water supply. In case of low input water pressure, call the helpline to get the booster installed

Can I open and service my purifier?

It is not recommend to open and service purifier by an individual. Call our Pureit Helpline if you face any issue which requires servicing and opening of the purifier

Can I use reject water?

It is not recommended to use the reject for any kind of human/pets consumption (drinking or cooking). It may be used for gardening or cleaning floors.

What should I do if any part of purifier is broken?

Please call the Pureit Helpline. Our technicians will visit your house and guide you on the repairs required. There will be a nominal visiting charge and you would need to buy the parts required

What should I do if there is leakage from the purifier?

First switch off the Ball Valve if you find any leakage from the purifier and turn off the power switch. Check for any visual improper fitment and then call our Pureit Helpline number and register a service request

How long the stored water in the Pureit Mineral RO+MF can be used for drinking?

You can used stored water for 2 days. If it is not used for more than 2 days we advise you to discard that water, refill and then consume

Disclaimer

*Under test condition, Input TDS-750 ppm, Turbidity-<1 NTU, Input Pressure-10 psi. Input Hardness-300 ppm, Temp.-room temp. When compared with annual maintenance contracts of branded ROs. Applicable for a family consuming 6000 litres in 1 year.

**Permeate flow rate and recovery are based on standard test conditions and may vary depending on input water quality, TDS, pressure and life of Filter elements

***Input water quality and TDS content are important determinants of output water quality.

****If input pressure exceeds 30 PSI, please install a company provided pressure reducing valve at an additional cost. If the pressure is lesser than 10 PSI then you need to buy 'Pressure enhancing pump at an additional cost. Device should not be installed in a house where input pressure is greater than 60 psi.

#Technical specifications are subject to change or improvement without prior notice

## In case the TDS is > 1000 ppm, a company provided anti-scalant is recommended to be installed, this has to be purchased at extra cost.

###If the iron content in the input water is more, it is recommended to install a company provided iron filter.

Physical product may vary from the image on the website